The ADHV4710 is a high-voltage, high-power, high-speed operational amplifier optimized for driving ±1 A of current into capacitive and resistive loads with a slew rate of ±1300 V/μs. This product integrates a high-voltage amplifier with low-voltage analog circuitry and an SPI-programmable digital engine, making it ideal for high-voltage applications such as automatic test equipment (ATE), programmable power supplies, and piezoelectric drive.
*Manufacturer product page: ADHV4710

■ Applications
- High voltage power amplifier (PA)
- High voltage SMU/VI source
・High-voltage arbitrary waveform generator (AWG)
・Piezoelectric transducer drive

■ Evaluation board
・ EVAL-ADHV4710

The AD4195-4 is a low noise, fully integrated analog front end for high precision measurement applications. The device contains a low noise, 24-bit Σ-Δ analog-to-digital converter (ADC) that can be configured with four differential inputs or eight single-ended/pseudo differential inputs. An on-chip, low noise gain stage allows small amplitude signals to be applied directly to the ADC.
*Manufacturer product page: AD4195-4

■ Applications
Industrial process control: PLC/DCS modules
- Temperature measurement
・Pressure measurement
Medical and scientific equipment
・Chromatography
・Environmental monitoring
Electronic Test and Measurement
・Measuring instruments
・Weight scale

The AD74416H is a 4-channel, software-configurable I/O device for industrial control applications. The AD74416H supports a wide range of uses, including analog I/O, digital I/O, RTD (resistance temperature detector), and thermocouple measurement capabilities.

Additionally, each channel has an integrated HART (Highway Addressable Remote Transducer) modem, and input/output communication and HART communication for all four channels are supported through a single SPI (Serial Peripheral Interface).
*Manufacturer product page: AD74416H

■ Applications
・Industrial control systems
・Process control
・Factory automation

■ Evaluation board
・EVAL-AD74416H

The MAX98415A is a highly efficient class-leading low quiescent power D Stereo speaker amplifier with envelope tracking control, brownout prevention engine (BPE), Dynamic Headroom Tracking (DHT), RMS It has a built-in limiter function.

MAX98415A High-precision output current monitoring (I _SENSE) and speaker feedback voltage (V _FEEDBACK) that allows the host device to run speaker protection algorithms. 192kHz sample rate and high passband (f _S > 50kHz) It supports high-resolution audio and ultrasound use cases, with separate bypass paths available for inputs such as ultrasound signals to ensure they are not attenuated by the audio processing. SSM and edge rate control, EMI Minimize the traditional class D Eliminates the need for output filtering, which is required by devices.
*Manufacturer product page: MAX98415A

■ Applications
・Soundbar
- Mobile speakers and smart speakers
- Tablets, laptops, and desktop computers
・Smart IoT devices

■ Evaluation board
・MAX98415AEVSYS

The MAX98425A is a highly efficient class-leading power supply with industry-leading low quiescent power consumption. D Stereo speaker amplifier with envelope tracking control, brownout prevention engine (BPE), Dynamic Headroom Tracking (DHT), RMS It has a built-in limiter function.

maximum 192kHz sample rate and high passband (f _S > 50kHz) It supports high-resolution audio and ultrasound use cases, with separate bypass paths available for inputs such as ultrasound signals to ensure they are not attenuated by the audio processing. SSM and edge rate control, EMI Minimize the traditional class D Eliminates the need for output filtering, which is required by devices.
*Manufacturer product page: MAX98425A

■ Applications
・Soundbar
- Mobile speakers and smart speakers
- Tablets, laptops, and desktop computers
・Smart IoT devices

■ Evaluation board
・MAX98425AEVSYS

The AD5460 is a 4-channel voltage and current output digital-to-analog converter (DAC) with a wide supply voltage range and flexible configurations. The AD5460 features adaptive power supply switching drivers integrated into each channel to minimize on-chip power consumption.

The adaptive power supply switching driver sets the required power supply voltage by selecting between a high voltage supply (AVDD_HI) and a low voltage supply (AVDD_LO) depending on the required output voltage level. The CHART pin allows a HART signal to be superimposed on the current output.
*Manufacturer product page: AD5460

■ Applications
・Factory automation
・Actuator control
・Group isolated analog output
・PLC and DCS applications
- HART network connection function

■ Evaluation board
EVAL-AD5460ARDZ

The LT8648SP synchronous step-down regulator utilizes the second-generation Silent Switcher architecture, which delivers high efficiency even at high switching frequencies while reducing EMI (electromagnetic interference). Integrated input and boost capacitors optimize the internal high-speed current loop and reduce board layout sensitivity, making it easier to achieve excellent EMI performance. This makes the LT8648SP ideal for noise-sensitive environments and applications.
*Manufacturer product page: LT8648SP

■ Applications
・Power supplies for automobiles and industrial equipment
・General-purpose step-down (buck) power supply

■ Evaluation board
・ DC2841A

The LTM4654 is a 300W output power µModule bus converter, a hybrid topology step-down DC-DC power supply with source/sink capability, featuring switching technology. The LTM4654 features an exposed power inductor on the top of the package, allowing for efficient heat dissipation away from the board.

The package includes a switching controller IC, power MOSFETs, and other supporting components, and the only external components required are flying (charge pump) capacitors, bulk capacitors for input and output bypass, and a few passive components for configuration.
*Manufacturer product page: LTM4654

■ Applications
Non-isolated intermediate bus power architecture
・Communication equipment, network equipment, test and measurement equipment
・Industrial applications

The LTM4719 is 42V Dual input, 150mA Synchronous Buck Power μModule (micromodule) regulator, I ² C It has an integrated battery health monitor that is interfaced via the VCCIO. An ultra-low quiescent current post-regulation linear regulator provides 5V at no load. 560nA (typical value) at full load 42μA (typical value), making it ideal for battery-powered portable devices.

The LTM4719 is 1 If one is lost, 2 Supports seamless transition between two input power sources. This automatic switchover eliminates the need for hold-up capacitors and minimizes the impact on the output rails. Burst Mode Quiescent current during operation 18.5μA Therefore, LTM4719 is suitable for many applications.
*Manufacturer product page: LTM4719

■ Applications
- Portable battery-powered devices
Wireless, healthcare, and industrial test equipment
・Uninterruptible power supply

■ Evaluation board
・ EVAL-LTM4719-AZ

The ADIN1101 is a low-power, single-port 10BASE-T1L transceiver designed for industrial Ethernet applications, compliant with the IEEE® 802.3cg-2019™ Ethernet standard for long-reach 10Mbps Single-Pair Ethernet (SPE). The ADIN1101 integrates an Ethernet physical layer (PHY) core with associated analog circuitry, input and output clock buffers, management interface control and subsystem registers, and a MAC interface and control logic for reset, clock control, and pin configuration management.
*Manufacturer product page: ADIN1101

■ Applications
・Process control
・Factory automation
・Building automation
・Field devices and switches

■ Evaluation board
・ EVAL-ADIN1100

The ADIN1111 is an ultra-low power, single-port 10BASE-T1L transceiver designed for industrial Ethernet applications, compliant with the IEEE® 802.3cg-2019™ Ethernet standard for long-distance 10Mbps Single Pair Ethernet (SPE).

The ADIN1111 integrates a media access control (MAC) interface and can directly connect to a variety of host controllers via a serial peripheral interface (SPI). The SPI enables the use of low-power processors without an integrated MAC, achieving the lowest overall system power consumption. The ADIN1111 is designed for edge-node sensors and field devices deployed in building, factory, and process automation.
*Manufacturer product page: ADIN1111

■ Applications
Building automation and fire safety
・Factory automation
・Status monitoring and device connection

■ Evaluation board
・ EVAL-ADIN1110

The MAX96792A is a dual GMSL™ 3/2 serial input to MIPI CSI-2 converter. The device receives forward channel video data while simultaneously transmitting and receiving bidirectional control channel data over coaxial or shielded twisted pair (STP) cable. The GMSL3 serial link, based on PAM-4, operates at 12 Gbps forward and 187.5 Mbps reverse.

The MAX96792A is backward compatible with GMSL2 and can be paired with a 6Gbps or 3Gbps GMSL2 serializer. Each GMSL input operates independently and can receive video with different timing and resolutions. The two GMSL links can also operate at different data rates, and video data from both inputs can be aggregated and output onto a single CSI-2 port or duplicated to a second output port for redundant processing. The device is configured using either an IC or UART interface. GPIO, IC, UART, and SPI tunneling functions are also available. The device is AEC-Q100 qualified.
*Manufacturer product page: MAX96792A

■ Applications
・Advanced Driver Assistance Systems (ADAS)
・8MP to 15MP forward-looking camera (FVC) system
- Aggregated transfer of camera data
・e-mirror camera system

■ Evaluation board
・MAX96716EVKIT

The MAX96793 GMSL™ serializer receives video over a MIPI CSI-2 interface and outputs it to a GMSL2 or GMSL3 serial link transceiver, while also transmitting and receiving bidirectional control channel data over the same GMSL link.

GMSL2 and GMSL3 data can be transmitted over coaxial or shielded twisted pair (STP) cables. The GMSL2 link operates at a fixed rate of 3 Gbps or 6 Gbps forward and 187.5 Mbps reverse. The GMSL3 link operates at a fixed rate of 12 Gbps forward and 187.5 Mbps reverse. The device is programmable over the link via a local IC/UART interface or a compatible deserializer. The MAX96793 includes two IC/UART pass-through channels, flexible GPIOs, an SPI tunnel, an integrated ADC, a temperature sensor, and extensive diagnostic features for functional safety. It is AEC-Q100 Grade 2 qualified over the automotive operating temperature range of −40°C to +105°C.
*Manufacturer product page: MAX96793

■ Applications
・Advanced Driver Assistance Systems (ADAS)
・8MP 60fps Forward Visible Camera (FVC) system
- Aggregated transfer of camera data
- Systems with multiple synchronized cameras

■ Evaluation board
・ MAX96793-AAK-EVK
・ MAX96793-ACK-EVK

The ADXL366 is an ultralow power, 3-axis micromachined electronics (MEMS) accelerometer that consumes only 0.96 μA at a 100 Hz output data rate and 191 nA in motion-triggered wake-up mode. Unlike accelerometers that achieve low power consumption through intermittent operation, the ADXL366 samples the full bandwidth of the sensor at all data rates rather than aliasing the input signal by undersampling.

The ADXL366 is capable of 14-bit output resolution. It also provides 8-bit formatted data for more efficient single-byte transfers when lower resolution is sufficient. ADXL362 Data is also provided in 12-bit format for design compatibility with other NI products. Measurement ranges are ±2g, ±4g, and ±8g, with a resolution of 0.25mg/LSB in the ±2g range.
*Manufacturer product page: ADXL366

■ Applications
- Continuous sensing
·hearing aid
Vital signs monitoring devices
Motion trigger power save switch
Motion-triggered weighing equipment
・Single-cell smartwatch
Smart Home

■ Evaluation board
・ EVAL-ADXL366