Analog Devices high-speed ADC: With AD9697, sample rate = 1 GSPS, JESD204B lanes (L) = 2, converters (M) = 2, octets (F) = 2, bits (N') = 16 decimation ratio is it ok to set to 4?

Analog Devices Digital Temperature Sensor: Setting the excitation current for the LTC2983 states "so that the maximum voltage drop is nominally 1.0V". What are the consequences if it exceeds 1.0V?

Analog Devices AD Converter : What should I do if the AD7124 does not output (Dout) due to SPI communication?

Does the Analog Devices RD Converter: Evaluation Board EVAL-AD2S1205SDZ come with a software CD?

Analog Devices AD Converter: Utilizes the AD7172-2 in single conversion mode. Please tell me the operation from writing the conversion start command (to register 0X01) to the first data output (issue /RDY signal pulse).

Analog Devices AD converter: The AD7328 absolute maximum rating for VDD to VCC is VCC -0.3 V to +16.5 V, but it is necessary to comply with this rule even when the power is turned on and off. is there?

Analog Devices AD Converter: Is the "Vref input current" value in the electrical characteristics table for the AD4680 an average value?

Does the Analog Devices power measurement IC: ADE78XXA support the IEC62053-22 standard?

Analog Devices power measurement IC: ADE78XXA is described in the datasheet as being compliant with the IEC62053-22 standard, but how can it be compliant with the accuracy standard class 0.1s, 0.2s, 0.5s, etc.?

Analog Devices AD Converter: AD9675 evaluation board for AD9671. Is it wrong?

Analog Devices ADC: How do I handle unused input pins for the AD7792?

Analog Devices High Speed A/D Converter: LTC2226 datasheet states, "For best performance, drive the analog inputs differentially. Each input is centered around a common mode voltage of 1.5V, ±0.5V on the 2V range, The 1 V range requires an amplitude of ±0.25 V." Could you please elaborate on this?

Analog Devices A/D Converter: What is the input range of the external VREF pin of the AD9213?

Analog Devices Power Measurement IC: I don't have an ADE7868A evaluation board, so is it possible to replace the ADE7878A on the ADE7878A evaluation board (EVAL-ADE7878A) with the ADE7868A for verification?

Analog Devices A/D converter : Is it a problem to assume that when AD7899's CS and RD are Low, the output does not become HI-Z and the data-converted output state is held continuously?

Analog Devices A/D Converter : Is it possible for AD7175-2 to use 1ch as a reference and use the remaining 4ch to measure the differential voltage?

Analog Devices Controller Board: Is it possible to combine a high-speed A/D converter evaluation board specified for ADS8-V1EBZ with the ADS8-V3EBZ controller board?

Analog Devices Multiplexed A/D Converters: Can multiple AD7682/AD7689 be used side by side for SPI parallel connection?

Analog Devices Precision A/D Converter: What is the state of each GPIO pin when the AD7172 powers up?

Analog Devices Isolated A/D Converter: What happens to the MDAT output on the secondary side when VDD1 on the ADuM7701 is absent?

Analog Devices Isolated A/D Converter: When using the ADuM7701, what happens to the secondary side output when the primary side power is lost while CLK continues to be supplied?

Analog Devices Precision A/D Converters: Can ceramic capacitors be used as the capacitors connected to CAP (pin 6), REF (pin 7), and VANA (pin 27) on the LTC1609?

Analog Devices Precision A/D Converter: Can the AD7124 evaluation software switch between bipolar/unipolar modes?

Analog Devices Precision A/D Converter: Please tell me how to calculate the temperature when RTD is selected in the result display in the AD7124 evaluation software.

Analog Devices Digital Temperature Sensors: How many 3-wire RTD Pt100s can be connected to the LTC2983/4/6?

Analog Devices R/D converter: What happens to the position information when the resolver is stationary in the AD2S1210?

I am using the Analog Devices isolated A/D converter: AD7400. How can I find the effective number of bits (ENOB) from the decimation ratio?

Analog Devices A/D converter (ADC): The temperature characteristics of the INL of the AD7134 are shown in Fig 40 of the datasheet, and it does not seem to have a particularly large temperature dependence, but this trend seems to change depending on the filter type. Is there any problem in determining that it is not?

Analog Devices Analog-to-Digital Converter (ADC): Is it okay to use an external precision voltage reference for the AD9680?

Analog Devices A/D converter (ADC) : Is it okay to use AD7891 parallel mode operation (Fig.2 in the data sheet) at the timing when RD or WR falls low before CS?