PS5169

10Gbps linear redriver for USB Type-C® enabled systems using an integrated USB3.2 / DisplayPort™ Alt Mode host device that includes an integrated USB Type-C® configuration switch. Provides linear redriver functionality for USB Tx and Rx signals. DisplayPort™ main link signals are also supported when DisplayPort™ Alt Mode is enabled.

Supports USB3.2 transport data rates up to 10Gbps (Gen2) and DisplayPort™ data rates up to 8.1Gbps (HBR3). The linear redriver feature compensates for PCB signal loss and other signal distortions, providing higher signal quality and compliance margins at your system's USB-C® receptacle. It also increases system design flexibility by allowing the system's USB Type-C® connector to be positioned further away from the integrated host device. For DisplayPort™ Alt Mode operation, the linear redriver incorporates Parade Technologies' patented AUX channel interception technology that adjusts high-speed data driver characteristics based on link training parameters reported by the downstream DisplayPort™ receiver is included.

■ Features & block diagram

・USB3.2 Gen2 x2 10Gbps dual lane operation and up to HBR3 8.1Gbps
DisplayPort™ Alt Mode support
- Integrated USB and DisplayPort™ Alt Mode ports
USB Type-C® application support
Supports full USB3.2 power management
・Compensate for PCB, cable and connector losses
programmable equalizer
・Waterproof IO design
- DisplayPort™ link training for RBR, HBR, HBR2 and HBR3
Field proven AUX intercept technology
・1.8V power supply
・Ultra low power consumption
- Deep sleep mode: 1.3uW
- Standby mode: 0.5mW
・2.7 x 3.7mm 26-pin QFN RoHS compliant and halogen-free package
・ESD: 8kV (HBM)

PS5170

10Gbps linear redriver for USB Type-C® enabled systems using an integrated USB3.2 / DisplayPort™ Alt Mode host device that includes an integrated USB Type-C® configuration switch. Provides linear redriver functionality for USB Tx and Rx signals. DisplayPort™ Main Link signals are also supported when DisplayPort™ Alt Mode is enabled.

It supports USB3.2 transport data rates up to 10Gbps (Gen2) and DisplayPort™ data rates up to 8.1Gps (HBR3). The linear redriver feature compensates for PCB signal loss and other signal distortions, providing higher signal quality and compliance margins at your system's USB-C® receptacle. It also increases system design flexibility by allowing the system's USB Type-C® connector to be positioned further away from the integrated host device. For DisplayPort™ Alt Mode operation, the linear redriver includes Parade Technologies' patented AUX channel interception technology that adjusts the characteristics of the high-speed data driver based on link training parameters reported by the downstream DisplayPort™ receiver. Built in.

■ Features & block diagram

・USB3.2 Gen2 x2 10Gbps dual lane operation and up to HBR3 8.1Gbps
DisplayPort™ Alt Mode support
- Integrated USB and DisplayPort™ Alt Mode ports
USB Type-C® application support
Supports full USB3.2 power management
・Programmable equalizer to compensate for PCB, cable and connector losses
・Waterproof IO design
- DisplayPort™ link training for RBR, HBR, HBR2 and HBR3
Field proven AUX intercept technology
・1.8V power supply
・Ultra low power consumption
- Deep sleep mode: 1.3uW
- Standby mode: 0.5mW
・3.1 x 4.4mm 34-pin QFN RoHS compliant and halogen-free package
・ESD: 8kV (HBM)

PS8769

Linear redriver for USB Type-C® enabled systems with an integrated USB3.2/ DisplayPort™ Alt Mode host device. Supports USB3.2 Gen1(5Gbps) / Gen2 (10Gbps) operation and DisplayPort™ Alt Mode operation up to HBR3 (8.1Gbps) link rate. It has a programmable equalizer that compensates for signal loss from PCB traces, cabling and connectors. DisplayPort™ Alt Mode support includes AUX intercept to enable response to link training commands. Full USB3.1 power management is supported.

Offers lower power and smaller footprint for USB-C® relay applications that do not require the full signal restoration performance of retimers. The small size and power combined with the single 1.8V power supply requirement make it ideal for handheld portable devices such as smartphones and tablets.

■ Features & block diagram

・USB3.2 Gen2 10Gbps and DisplayPort™ Alt Mode support up to HBR3 8.1Gbps
- USB and DisplayPort™ Alt Mode ports with integrated port configuration switch
Integrated USB Type-C® application support
Supports full USB3.1 power management
・Programmable equalizer to compensate for PCB, cable and connector losses
- DisplayPort™ link training for RBR, HBR, HBR2 and HBR3
Field proven AUX intercept technology
・1.8V single power supply
・2.7 x 3.7mm 26-pin QFN RoHS compliant and halogen-free package
・ESD: 4kV (HBM)

PS8815

10Gbps retimer for USB Type-C® enabled systems using an integrated USB3.2 host/DisplayPort™ Alt Mode video source device with an integrated USB Type-C® configuration switch. For USB3.2 Tx and Rx signals, it provides retiming for Gen2 operations and redrive for Gen1 operations. In DisplayPort™ Alt Mode, provides re-drive of DisplayPort™ main link signal.

It supports USB3.2 transport data rates up to 10Gbps (Gen2) and DisplayPort™ data rates up to 8.1Gbps (HBR3). Retiming and re-driving signal repeater functions compensate for PCB signal loss and other signal distortions, providing higher signal quality and compliance margins. It also increases system design flexibility by allowing the system's USB Type-C® connector to be positioned further away from the integrated host device. The DisplayPort™ Redriver feature incorporates Parade Technologies' patented AUX channel interception technology that adjusts high-speed data driver characteristics based on link training parameters reported by the downstream DisplayPort™ receiver.

■ Features & block diagram

・Compliant with VESA DisplayPort™ Alt Mode of USB Type-C® standard 1.0b
・Compliant with USB Power Delivery 3.0
・Compliant with USB Type-C® port controller interface specification 2.0
・Up to USB3.2 Gen2 10Gbps and HBR3 8.1Gbps
Supports DisplayPort™ 1.4a Alt Mode
・Built-in BMC PHY and protocol
Configurable DFP/UFP/DRP support
・Built-in CC logic and automatic power management
・USB3.2 Gen2 10Gbps retiming
・DisplayPort™ 1.4a HBR3 8.1Gbps re-driving
・CrystalFree: No external crystal or clock required
・System transparent operation (operation like redriver)
・High input jitter tolerance and low output jitter
・UniEye™ equalizer to compensate for channel loss
・Very low latency: total propagation delay less than 1ns
・Integrated VCONN power switch
GPIO for VBUS switch and other system control
・I2C slave (TCPCI) with IRQ#
・Low active power consumption
・Ultra-low standby power consumption
・5 x 6.5 mm 52-pin QFN halogen-free RoHS package
・3V and 1.2V power supply
・ESD: 8kV (HBM)

PS8818

10Gbps retimer for USB Type-C® enabled systems that use an integrated USB 3.1 / DisplayPort™ Alternate Mode host device that includes an integrated USB Type-C® configuration switch. Provides selectable retiming or re-driving of USB Tx and Rx signals, and re-driving of DisplayPort™ main link signals when DisplayPort™ Alt Mode is enabled. Port configuration switching is not included.

It supports USB3.1 transport data rates up to 10Gbps (Gen2) and DisplayPort™ data rates up to 8.1Gbps (HBR3). Retiming and re-driving signal repeater functions compensate for PCB signal loss and other signal distortions for higher signal quality and compliance margins. It also increases system design flexibility by allowing the system's USB Type-C® connector to be positioned further away from the integrated host device. The DisplayPort™ Redriver feature incorporates Parade Technologies' patented AUX channel interception technology that adjusts high-speed data driver characteristics based on link training parameters reported by the downstream DisplayPort™ receiver.

■ Features & block diagram

Integrated DisplayPort™ Alt Mode and USB-C® port switching
Designed for USB-C® enabled systems using USB host devices
・USB3.1 Gen2 10Gbps and up to HBR3 8.1Gbps
Supports DisplayPort™ Alt Mode
Supports full USB3.1 power management
・USB3.1 Gen2 10Gbps retiming
・Re-driving with DisplayPort™ 1.4 HBR3 8.1Gbps automatic AUX snooping
Integrated AUX switch for USB-C® SBU signals
・Crystal Free: No external crystal or clock required
・UniEye™ adaptive equalizer and programmable equalizer to compensate for PCB loss
・Supports DisplayPort™ link training for RBR, HBR, HBR2, HBR3
Field proven AUX intercept technology
・Ultra-low latency
·Low power consumption
・3.3V and 1.2V power supply
・4x6mm 40-pin and 3.1x4.4mm 34-pin QFN RoHS compliant & halogen-free packages
・ESD: 7kV (HBM)

PS8828

Addresses fast signal switching and signal integrity requirements for implementing USB Type-C® (or USB-C®) connectors to USB host devices that support the VESA® DisplayPort™ Alt Mode Standard. Supports USB3.2 Gen2 x2 configurations and DisplayPort™ data rates up to 8.1Gbps (HBR3). A signal retiming feature is included to compensate for PCB signal loss and other signal distortions.

■ Features & block diagram

・USB3.2 Gen2 x2 10Gbps dual lane operation and
Supports DisplayPort™ Alt Mode up to HBR3 8.1Gbps
・With integrated USB and DisplayPort™ Alt Mode ports
Supports USB Type-C® applications
・Supports USB3.2 Gen2 10Gbps retiming
・Fast Low Frequency Periodic Signaling (LFPS) enter/exit time
・Crystal Free: No external crystal or clock required
Supports DisplayPort™ 1.4a HBR3 8.1Gbps re-driving and AUX auto snooping
・Built-in 100Ω differential termination resistors for input and output
・Programmable equalizer to compensate for PCB loss
- DisplayPort™ link training for RBR, HBR, HBR2, HBR3
Field proven AUX intercept technology
・Ultra-low latency
·Low power consumption
・When using the on-chip integrated switching DC/DC of the 3.3V to 1.2V core power supply,
Single 3.3V power supply
・6x6mm 105 ball BGA package
・ESD: 8kV (HBM)

PS8828A

Addresses fast signal switching and signal integrity requirements for implementing USB Type-C® (or USB-C®) connectors to USB host devices that support the VESA® DisplayPort™ Alt Mode Standard. Supports USB3.2 Gen2 x2 configuration and DisplayPort™ data rate up to 8.1Gbps (HBR3). A signal retiming feature is included to compensate for PCB signal loss and other signal distortions.

■ Features & block diagram

・USB3.2 Gen2 x2 10Gbps dual lane operation and
Supports DisplayPort™ Alt Mode up to HBR3 8.1Gbps
・With integrated USB and DisplayPort™ Alt Mode ports
Supports USB Type-C® applications
・Supports USB3.2 Gen2 10Gbps retiming
・Fast Low Frequency Periodic Signaling (LFPS) enter/exit time
・Crystal Free: No external crystal or clock required
Supports DisplayPort™ 1.4a HBR3 8.1Gbps re-driving and AUX auto snooping
・Built-in 100Ω differential termination resistors for input and output
・Programmable equalizer to compensate for PCB loss
- DisplayPort™ link training for RBR, HBR, HBR2, HBR3
Field proven AUX intercept technology
・Ultra-low latency
·Low power consumption
・3.3V and 1.2V power supply
・6x6mm 105 ball BGA and 4x6mm QFN40 package
・ESD: 8kV (HBM)

PS8836

USB3.2, DisplayPort™ 2.1 retimer for host applications. It is compliant with the USB3.2 specification and related USB-IF specifications for retimer and Alt Mode support, and is compliant with the VESA® DisplayPort™ Alt Mode of the USB Type-C® 2.0 standard. Support for USB3.2 Gen2 x2 and DisplayPort™ 4 lanes up to UHBR20, plus USB3.2 Gen2 x1 multi-lanes with support for DisplayPort™ 1 or 2 lanes as defined by the DisplayPort™ Alt Mode standard. Support functional operation.

Provides a simple, yet versatile, high-performance retimer solution for high-speed signal integrity and compliance margins in USB-C® receptacles. It not only provides ultra-low standby power and extends system battery life, but also extends DisplayPort™ 2.1 ecosystem and user experience. The PS8836 is also pin-compatible with the PS8833, helping customers design a common PCB for greater diversity in I/O specifications.

■ Features & block diagram

・Supports USB3.2 Gen2 x2 20Gbps dual lane operation
・Low power U1, U2, U3
・Supports DisplayPort™ Alt Mode
・Supports USB3.2 specification Retimer architecture
・Supports DisplayPort™ 2.1 up to UHBR20 20Gbps
・RBR, HBR, HBR2, HBR3, UHBR10, UHBR13.5, UHBR20
DisplayPort™ LT Tunable PHY Retimer (LTTPR) transparent and
Supports non-transparent mode
・Supports DisplayPort™ P2.1 Advanced Link Power Management (ALPM)
・Integrated AUX switch for USB Type-C® applications
・Adaptive CTLE and DFE equalizer
・Built-in 85Ω differential termination resistor for input and output
·Low power consumption
・3.3V and 0.9V power supply
・4.7 x 8.0mm 62-pin QFN package
・ESD: 5kV (HBM)

Parade Technologies Manufacturer Information Back to Top

Parade Technologies Manufacturer Information If you would like to return to the top page, please click below.