The AD4080 is a high speed, low noise, low distortion 20-bit Easy Drive successive approximation register (SAR) analog-to-digital converter (ADC). The AD4080 maintains high performance (signal-to-noise and distortion (SINAD) ratio > 90 dBFS) at signal frequencies above 1 MHz, enabling a wide range of precision, wide bandwidth data acquisition applications. For applications that do not require the lowest latency of the AD4080, oversampling can be applied and the integrated digital filtering and decimation can be used to simplify the input antialiasing filter design, reduce noise, and lower the output data rate.
*Manufacturer product page: AD4080

■ Applications
Digital Imaging
Cell analysis
Spectroscopy
ATE (Automatic Test Equipment)
- High speed data acquisition
・Digital control loop, hardware in the loop
- Power quality analysis
・Source measure unit
・Electron microscope and X-ray microscope
Radar level measurement
Non-destructive testing
Preventive maintenance and structural condition monitoring

■ Evaluation board
・ EVAL-AD4080-FMC

The ADAQ7768-1 is a 24-bit precision data acquisition (DAQ) μModule® system that encapsulates signal conditioning, conversion, and processing blocks into a single system-in-package (SiP) design, enabling the rapid development of extremely compact, high performance, and precision DAQ systems.
*Manufacturer product page: ADAQ7768-1

■ Applications
・Universal input measurement platform
Electronic test and measurement
・Sound and vibration, acoustics and material science research and development
Control and hardware-in-the-loop verification
- Condition monitoring for preventive maintenance
Audio testing

■ Evaluation board
EVAL-ADAQ7768-1
EVAL-ADMX1001

The MAX22516 IO-Link data link controller integrates a 24V C/Q transceiver, auxiliary digital inputs and outputs, integrated DC-DC, 5V and 3.3V linear regulators and a full-featured IO-Link data link controller. Once configured, the MAX22516 data link controller operates the IO-Link transceiver and requires no intervention from an external microcontroller during normal operation. Instead, the IO-Link transceiver can be controlled directly using the UART interface (TXEN, TX and RX) or through the Serial Peripheral Interface (SPI). The data link controller supports receive and transmit buffers for IO-Link communication. Buffers for maximum size process data, ISDUs, events and page data reduce the need for time-critical microcontroller intervention, allowing the microcontroller to focus on application layer tasks.
*Manufacturer product page: MAX22516

■ Applications
IO-Link sensor and actuator devices
・Industrial sensors

■ Evaluation board
・ MAX22516EVKIT

The MAX9295D converts single- or dual-port MIPI CSI-2 data streams to GMSL2™ or GMSL1™, while transmitting and receiving control channel data, enabling full-duplex, single-wire transmission of forward video data and bidirectional control data over cable lengths of over 15m. In GMSL2 mode, the device operates at fixed rates of 3Gbps or 6Gbps in the forward direction and 187.5Mbps in the reverse direction. In GMSL1 mode, the MAX9295D can be used with a first-generation 3.12Gbps or 1.5Gbps GMSL1 deserializer, or with a GMSL2 deserializer configured in GMSL1 mode and operate at up to 4.5Gbps. Operation is specified over the automotive temperature range of -40°C to +105°C, and the device is AEC-Q100 Grade 2 qualified. The cable can be coax or shielded twisted pair (STP).
*Manufacturer product page: MAX9295D

■ Applications
Co-located sensors
・Stereo camera
・Side mirror
·radar
・LiDAR

■ Evaluation board
・MAX9295DEVKIT

The MAX22910 is an industrial high-side switch operating as a current-sourcing output device. The high-side switch has an on-resistance (RON) of 21mΩ (typical) and 40mΩ (maximum). The maximum load current is limited and set by the CURLIM resistor from 0.7A to 9A with ±10% accuracy. At an ambient temperature of +100°C, the maximum continuous load current is 7A. The MAX22910 is specified to operate with a supply voltage up to 80V, as long as OUT does not go below GND. The logic interface voltage level can be flexibly set from 1.6V to 5.5V by the VL logic supply.
*Manufacturer product page: MAX22910

■ Applications
・Industrial digital output module
・Safety output module
・Commercial vehicle controller
・Motor holding brake

■ Evaluation board
・ MAX22910EVKIT

The ADuM6221A is a dual-channel digital isolator and isoPower®, integrated isolated dc-dc converter. Based on Analog Devices' iCoupler® technology, the dc-dc converter provides isolated, regulated power. It meets CISPR 32/EN 55032 Class B emissions limits at full load on a 2-layer printed circuit board (PCB) with ferrite beads. The ADuM6221A eliminates the need for a separate isolated dc-dc converter in 500 mW isolated designs. It also uses iCoupler chip-scale transformer technology for both the logic signal isolation and the magnetics of the dc-dc converter, resulting in full circuit isolation in a small size.
*Manufacturer product page: ADuM6221A

■ Applications
・RS-232 transceiver
Power supply start-up bias and gate drive
・Isolated sensor interface
・Automotive On-Board Charger (OBC) and DC-DC
・Industrial programmable logic controllers (PLCs)

■ Evaluation board
・ EVAL-ADUM6421A

The MAX17793 is a high-efficiency, high-voltage, synchronous step-down DC-DC converter with integrated MOSFETs that operates over an input voltage range of 3V to 80V. The device can deliver up to 3A of current and generate output voltages ranging from 0.6V to 90% of VIN, and features a MODE/SYNC pin that can be used to program the device in forced pulse-width modulation (PWM) or switching frequency modulation (SFM) operating modes and to synchronize the internal clock to an external clock. It also features an enable/input undervoltage lockout (EN/UVLO) pin to program the required input voltage at which the converter turns on/off, and a soft-start (SS) pin to reduce inrush current during startup. Additionally, it features a RESET/TJ pin that can be used to monitor the status of the output voltage or die temperature. The die temperature monitor allows the device to directly measure the temperature of the silicon die rather than relying on theoretical estimates, enabling a more robust and reliable power supply design.
*Manufacturer product page: MAX17793

■ Applications
Industrial, avionics and heavy machinery
・Factory and building automation
Motor control
・General-purpose power supply

■ Evaluation board
・ MAX17793EVKITA

The MAX77505 is a low quiescent current (800nA typical), highly efficient hysteretic step-down converter that operates over an input voltage range of 2.5V to 16V. High efficiency is achieved across the entire load range, making it ideal for applications powered by primary or 4-cell alkaline batteries with short operating times and long standby/idle times, such as asset trackers and door lock devices. One of 30 preset output voltages from 0.8V to 5.5V is resistor-selected (RSEL). To protect the system and the device itself, input undervoltage lockout, cycle-by-cycle switch current limit, and thermal shutdown are provided. The device is available in a 10-pin FC2QFN package (2.0mm x 2.0mm x 0.55mm).
*Manufacturer product page: MAX77505

■ Applications
・2-3 cell Li-Ion battery applications
・4-cell alkaline battery application
・IoT, wearable devices
-Smart meters, door locks, asset trackers, etc.

■ Evaluation board
・MAX77505EVKIT

The TMCM-2611-AGV is a 2-axis servo drive platform for 3-phase BLDC motors operating at up to 14ARMS at +48V. It provides RS485, CAN, and USB interfaces with TMCLTM protocol for communication. The TMCM-2611-AGV supports a variety of position feedback options including incremental quadrature encoders and digital Hall sensors.
*Manufacturer product page: TMCM-2611-AGV

■ Applications
Robotics
・Lab automation
·Manufacturing
・Factory automation
・Servo drive
・Industrial motor drives

Operating at speeds up to 1GHz, the ADSP-SC598 processor is part of the ADSP-SC59x SHARC® family. It uses the same dual SHARC+® DSP core architecture as the ADSP-SC594/SC592/SC591, but the integrated Arm core has been upgraded to a Cortex-A55 running at up to 1.2GHz. With FPU and Neon® DSP extensions, the A55 processor also handles real-time processing tasks and manages peripherals to connect to time-critical data for audio applications. These interfaces include Gigabit Ethernet, USB High-Speed, CAN FD, and a wealth of other connectivity options for flexible and simplified system design.
*Manufacturer product page: ADSP-SC598

■ Applications
・Automotive:
- Audio Amplifiers
- Head Unit
- ANC/RNC
- Rear Seat Entertainment
- Digital Cockpit
- Advanced Driver Assistance Systems (ADAS)
Consumer and professional audio:
- Speaker
- Sound Bar
- AVR
- Conference System
- Mixing Console
- Microphone Array
- Headphones

■ Evaluation board
・ EV-SC598-SOM